MENU
In case you want to know
how I'm doing,
Deer Valley, Arizona
02345 hits
since 06/17/2005
Z31 4 to 5 Lug Swap Information - Rear
 | |||||||
|---|---|---|---|---|---|---|---|
| Order | Part Code | Description | Part Numbers | Applied Model | Rear Axle Flange | Control Arm | Stub Axle |
| 1 | 39600M(RH) 39601(LH) |
Drive Axle (Half Shaft) | 39600-07F15(RH) 39601-07F15(LH) |
Non-Turbo | Any non-turbo | Any | Any |
| 39600-24P00(RH) 39601-24P00(LH) |
Turbo | Any turbo | |||||
| 2 | 38162A | Lock Nut | 43262-01P10 | All | Any | Any | Any |
| 3 | 43213 | Rear Axle Flange | 43213-61L00 | 84-86 Non-T | Any 84-86 | Any | |
| 43213-F6500 | 84-86 Turbo | ||||||
| 43213-21P05 | 87-89 Non-T | Any 87-89 | |||||
| 43213-22P05 | 87-89 Turbo | ||||||
| 4 | 43252 | Rear Axle Shaft Oil Seal (Inner) | 43232-21000 | 84-86 All | Any 84-86 | Any 84-86 | Any |
| 43232-F6100 | 87-89 All | Any 87-89 | Any 87-89 | ||||
| 5 | 43210 | Rear Axle Bearing (Inner) | 43210-21000 | All | Any | Any | Any |
| 6 | 43090 | Distance Piece | 43090-01P00 | Mark A | Any | Any | Any |
| 43091-01P00 | Mark B or none | ||||||
| 43092-01P00 | Mark C | ||||||
| 7 | 55501(RH) 55502(LH) |
Control Arm | 55501-01P00(RH) 55502-01P00(LH) |
84-86 All | Any 84-86 | Any | |
| 55501-21P10(RH) 55502-21P10(LH) |
87-89 All | Any 87-89 | |||||
| 8 | 43215 | Rear Axle Bearing (Outer) | 43215-19P00 | 84-86 All | Any | Any 84-86 | Any |
| 43215-21P05 | 87-89 All | Any 87-89 | |||||
| 9 | 43070 | Rear Axle Bearing Spacer (outer) | 43070-01P00 | All | Any | Any | Any |
| 10 | 38162 | Rear Axle Shaft | 38162-01P11 | 4 lug | Any | Any | |
| 38162-02P01 | 5 lug | ||||||
| 11 | 43222 | Hub Bolt / Stud | 43222-91P00 | All | Any | Any | Any |
| 12 | 43242 | Rear Axle Grease Catcher | 43242-01P00 | 4 lug | Any | Any | Any 4 lug |
| 43242-02P00 | 5 lug | Any 5 lug | |||||
| 13 | 43207 | Rear Disk Brake Rotor | 43206-P9601 | 84-85 4 lug | Any | Any | Any 4 lug |
| 43206-02P01 | 84-86 5 lug | Any 5 lug | |||||
| 43206-24P01 | 87-89 All | ||||||
Going by all this, the actual axle stubs are completely interchangable. Just be aware of the inner axle flange and the bearings.
The way I read it, to do a 4 to 5 lug swap, all you need is the 5 lug axle shafts (with the grease catchers and wheel studs) (part number 38162-02P01 x2) and the appropriate 5 lug rotor (part number 43206-02P01 x2). Of course, since you're pulling everything apart, it would be a good time to inspect and possibly replace the bearings and install with new oil seals and grease.